- |
SIMATIC DP, ET 200ECO PN, 8 DO 24V DC/1,3A; 8 X M12, DEGREE OF PROTECTION IP67 |
|
| General information |
| Vendor identification (VendorID) |
002AH |
| Device identifier (DeviceID) |
0306H |
| Supply voltage |
| Load voltage 1L+ |
| Rated value (DC) |
24 V |
| permissible range, lower limit (DC) |
20.4 V |
| permissible range, upper limit (DC) |
28.8 V |
| Reverse polarity protection |
Yes |
| Load voltage 2L+ |
| Rated value (DC) |
24 V |
| permissible range, lower limit (DC) |
20.4 V |
| permissible range, upper limit (DC) |
28.8 V |
| Reverse polarity protection |
Yes |
| Input current |
| from load voltage 1L+ (unswitched voltage) |
4 A |
| from load voltage 2L+, max. |
4 A |
| Power losses |
| Power loss, typ. |
5.5 W |
| Digital outputs |
| Number of digital outputs |
8 |
| In groups of |
4 |
| Short-circuit protection |
Yes |
| Response threshold, typ. |
1,8 A |
| Limitation of inductive shutdown voltage to |
Typ. (L1+, L2+) -47 V |
| Controlling a digital input |
Yes |
| Switching capacity of the outputs |
| on lamp load, max. |
5 W |
| Output current |
| for signal "1" rated value |
1.3 A; Maximum |
| for signal "0" residual current, max. |
1.5 mA |
| Parallel switching of 2 outputs |
| for increased power |
No |
| for redundant control of a load |
Yes |
| Switching frequency |
| with resistive load, max. |
100 Hz |
| with inductive load, max. |
0.5 Hz |
| on lamp load, max. |
1 Hz |
| Aggregate current of outputs (per group) |
| all mounting positions |
| up to 60 °C, max. |
3.9 A |
| Cable length |
| Cable length unshielded, max. |
30 m |
| Interfaces |
| Transmission procedure |
100BASE-TX |
| Transmission rate, max. |
100 Mbit/s |
| Supports protocol for PROFINET IO |
| Number of PROFINET interfaces |
1 |
| Autocrossing |
Yes |
| Automatic detection of transmission speed |
Yes |
| Integrated switch |
Yes |
| PROFINET IO Device |
| IRT with the option "high flexibility" supported |
Yes |
| Prioritized startup |
Yes |
| Protocols |
| Supports protocol for PROFINET IO |
Yes |
| PROFINET CBA |
No |
| Supports protocol for PROFIsafe |
No |
| Protocols (Ethernet) |
| SNMP |
Yes |
| DCP |
Yes |
| LLDP |
Yes |
| ping |
Yes |
| ARP |
Yes |
| Interrupts/diagnostics/status information |
| Status indicator |
Yes; Green LED |
| Alarms |
| Diagnostic alarm |
Yes |
| Diagnostic messages |
| Diagnostic functions |
Yes |
| Diagnostic information readable |
Yes |
| Monitoring the supply voltage |
Yes; Green "ON" LED |
| Wire break in actuator cable |
Yes |
| Short circuit |
Yes |
| Group error |
Yes; Red/yellow "SF/MT" LED |
| Galvanic isolation |
| between the load voltages |
Yes |
| between load voltage and all other switching components |
No |
| between Ethernet and electronics |
Yes |
| Galvanic isolation digital outputs |
| between the channels |
No |
| Permissible potential difference |
| between different circuits |
75 VDC / 60 VAC |
| Isolation |
| tested with |
| 24 V DC circuits |
500 V |
| Interface |
1500 V; According to IEEE 802.3 |
| Degree and class of protection |
| IP65 |
Yes |
| IP66 |
Yes |
| IP67 |
Yes |
| Connection method |
| M12 |
Yes |
| Dimensions |
| Width |
60 mm |
| Height |
175 mm |
| Depth |
49 mm |
| Weights |
| Weight (without packaging) |
910 g |
| Status |
Jun 6, 2014 |
